This page is general information. The rules that apply to welding at work are in OSHA's standards, including 29 CFR 1910.252 for welding, cutting and brazing. Start at OSHA's welding, cutting and brazing page, check local fire codes, and follow the manual for your machine. Where they differ from this page, follow them.
What is in welding fumes
Welding fumes are a mix of fine metal particles and gases. The particles come from the base metal, the filler and any coating on the surface. The gases come from the shielding gas, the flux and the heat of the arc acting on air. What is in the plume depends on what you weld, so fumes from bare mild steel differ from those off stainless or galvanized steel.
Short-term effects include eye, nose and throat irritation, dizziness and nausea. Longer exposure is linked to lung problems and other illness. That is why the first rule is simple: keep your head out of the plume.
Ventilation that works
- Position yourself. Stand so the fumes rise away from your face, not up into your helmet. Shift sideways rather than leaning over the work.
- Move air across the work. Open doors and use a fan to pull fumes away from you. Keep the airflow gentle at the arc if you use shielding gas, since a strong draft blows the gas away.
- Use local exhaust. A fume extractor with its hood placed close to the arc captures fumes at the source. It is the best option indoors.
- Never weld in a small closed space such as a tank or crawlspace without proper ventilation, training and procedures. Shielding gases can displace oxygen there.
Coatings and residues to deal with first
| Surface | Concern | What people do |
|---|---|---|
| Galvanized steel (zinc) | Zinc fumes can cause metal fume fever, a flu-like illness | Grind the coating off the weld area and use strong ventilation |
| Stainless steel | Fumes can contain hexavalent chromium, a known hazard | Use local exhaust and follow OSHA guidance on it |
| Paint, oil and grease | Burns into smoke and irritating gases | Strip and clean the area before welding |
| Parts cleaned with chlorinated solvents | Heat from the arc can turn the vapor into toxic gas, including phosgene | Keep these solvents away from welding and let parts dry fully |
More on metals in metals for beginners.
Fire safety
Sparks and spatter can bounce and roll across a floor, drop through cracks and land in places you cannot see. OSHA's general industry rule uses a 35-foot (about 11 m) distance: combustibles within that range should be moved away or covered with fire-resistant material, or someone should keep a fire watch. Read the current OSHA text for the details.
- Sweep the floor and clear sawdust, rags, paper, cardboard and fuel cans from the area.
- Cover anything that cannot be moved with a welding blanket, and check for gaps in walls and floors where sparks could fall through.
- Keep a fire extinguisher suited to the hazards within reach, and know how to use it.
- Never weld or cut a drum, tank or container that held fuel or another flammable without proper cleaning procedures. Fumes left inside can explode.
- After you finish, keep watching the area. OSHA's rule calls for a fire watch for at least 30 minutes after hot work where a fire watch is required. Smoldering can start long after the last spark.
Electric shock
Welding circuits carry enough current to injure you. Keep gloves and clothing dry, do not weld standing in water or on a wet floor, and never touch the electrode or wire and the metal you are welding at the same time with bare skin. Inspect cables for cracked insulation, and turn the machine off before changing rods, tips or tungsten. The machine manual lists its grounding and power requirements.
Gas cylinders
Keep cylinders upright and chained or strapped so they cannot fall. Leave the valve cap on when a regulator is not attached, keep cylinders away from the arc and sparks, and close the valve when you finish. Never strike an arc on a cylinder.
Fume and fire questions
Is it safe to weld in my garage?
Many people do with doors open, fumes directed away, combustibles cleared and a fire extinguisher nearby. Check local codes and your machine's power needs, and keep vehicles, fuel and solvents out of range.
What is metal fume fever?
A short flu-like illness after breathing fumes from some metals, most often zinc from galvanized steel. If you feel ill after welding, stop and get medical advice.