The five basic joints
Butt joint
Groove weld
Two pieces edge to edge in the same plane. Thin sheet can be welded with a small gap; thicker plate gets a beveled groove so the weld reaches the root.
Lap joint
Fillet weld
One piece overlaps the other. A fillet weld runs along the edge of the top piece. Forgiving on fit-up, so it is a good early practice joint.
T-joint
Fillet weld
One piece stands square on the face of another. Fillet welds go in one or both corners. Brackets, frames and stands are full of them.
Corner joint
Fillet or groove weld
Two pieces meet at a right angle to form an L, as in a box or a frame. The weld can go inside the corner, outside it, or both.
Edge joint
Edge weld
Two pieces lie side by side and the weld runs along their shared edges. Mostly used on thin sheet that will not carry much load.

Fillet welds and groove welds
Most welds are one of two types:
- Fillet welds fill the corner where two pieces meet at an angle, as in T-joints, lap joints and inside corners. Seen in cross-section they look like a triangle. The size of a fillet is measured by the length of its legs.
- Groove welds fill a gap or a beveled channel between pieces, as in butt joints. On thicker plate the edges are often beveled into a V so the weld can reach the bottom of the joint, which is called the root.
A weld that does not reach the root or does not melt into both pieces may look fine on top and still be weak. That is why practice welds get cut open or bent to check them. See practice projects.
Welding positions
Positions describe where the weld sits relative to you and gravity. They are numbered 1 to 4, and an F or G shows whether the weld is a fillet or a groove. So 2F is a horizontal fillet weld and 3G is a vertical groove weld.
| Number | Position | Fillet code | Groove code | What it is like |
|---|---|---|---|---|
| 1 | Flat | 1F | 1G | The weld is on top and you work downward into it. Gravity helps, so start here. |
| 2 | Horizontal | 2F | 2G | The weld runs sideways along a wall. The puddle tends to sag toward the lower plate. |
| 3 | Vertical | 3F | 3G | The weld runs up or down a wall. Most steel work goes uphill for better penetration. |
| 4 | Overhead | 4F | 4G | The weld is above you. The puddle wants to drip, so heat and puddle size stay small. |
Pipe adds more positions (5G and 6G, for example) where the pipe is fixed and the welder moves around it. Those come later. Learn to make sound flat welds first, then move one position at a time.
Fit-up and tacking
- Cut and clean the pieces. Square, clean edges fit better and weld easier.
- Clamp the parts in position. Use a square to check angles before welding anything.
- Set a consistent gap if the joint needs one. A gap that changes along the joint makes the weld change too.
- Tack weld at each end and at intervals along longer joints. Tacks are short welds that hold the parts in place.
- Check the fit again, since tacks pull parts as they cool. Adjust, then weld the full joint.
Weld distortion is the main reason parts come out crooked. Alternate sides, weld in short sections and let the part cool, so the pulling forces balance out.
Reading a finished weld
A sound beginner weld has even width and evenly spaced ripples, blends smoothly into both pieces at the edges, and has no holes, cracks or undercut (a groove melted into the base metal along the weld edge). For anything structural, appearance is not enough: welds that carry loads need qualified welders, proper procedures and inspection.
Joint questions
Which joint should I practice first?
A lap joint or a T-joint in the flat position. Both are forgiving to fit up and teach you to aim the arc into a corner.
What does "full penetration" mean?
The weld fuses through the entire thickness of the joint, all the way to the root. It matters for groove welds that need full strength.